Print Seller Tools

3D print time calculator

Enter your slicer’s estimate and what it said against what it took on a few past prints, and get the time to quote and what that machine time costs.

How do you want to estimate?
Your slicer’s estimate
hExample. From the slicer.
min
Past prints, slicer against clock
h4 h 30 min is 4.5. 0 if unused.
h
h
h
h
h

Optional. Leave these at 0 and the slicer’s time is shown as it is. Enter your own, from one to three prints, to correct it.

The part and the speed
gFilament used, from your slicer.
cm³Plastic deposited, with infill and walls.
g/cm³
mm
mmUsually close to the nozzle diameter.
mm/sLower than the top speed: printers slow in corners.
mm³/s0 for none. Enter your hotend’s limit if you know it.
%Extra time for travel, retraction, heating, slow layers. Yours to set.

Slicers do this far more carefully. Use this only when you have no slicer figure. Starting values are examples, not research.

What an hour of the printer costs
W
$/kWhExample. Read yours on your bill.
$Example. Include tax and shipping.
$Example. 0 if you would scrap it.
hExample. Hours before you replace it.
hExample. Time it is actually running.
$/yrExample. Nozzles, belts, build plates, lubricant.
%Example. Count your own failed prints for a month.
%A share of the charge, not a markup on cost.

105 W, average while printing PLA.

Working it out…

How this is worked out

Two ways to get a time, and one way to price it.

Correcting your slicer

A slicer works from the speeds and accelerations in its machine profile. Your printer may not reach them, and no website can know by how much. You can: print a few things, note what the slicer said, note what the clock said, and use the ratio. This page adds the times up before dividing, so a long print counts for more than a short one.

Correction factor = total hours it took ÷ total hours the slicer said, over the past prints you enter

Print time = the slicer’s estimate × correction factor

With no past prints the factor is 1 and the slicer’s time is shown unchanged.

Rough, with no slicer

A printer can only push so much plastic through the nozzle each second. That flow is the width of the line, times the height of the layer, times how fast the head moves. The time is the volume of plastic divided by that flow, plus the overhead you choose.

Volume = weight ÷ density (or the volume you enter)

Flow = line width × layer height × speed, in mm³ per second, no more than the hotend limit if you enter one

Printing time = volume × 1000 ÷ flow ÷ 3600, in hours

Print time = printing time × (1 + overhead)

What the time costs

The hour cost is the one on the cost per hour calculator, worked by the same code: depreciation, maintenance, power and failed prints.

Machine cost of the print = print time × cost per good print hour

Machine time to charge for = print time × charge per hour at your margin

Assumptions

  • The rough mode is a rough mode. It treats the print as one steady stream of plastic, which no print is. It does not know about supports, bridges, small features, cooling pauses or how your firmware plans moves. Overhead stands in for all of that and is a number you choose, not one we measured. This page gives no accuracy figure for it, because none that we could cite would fit your printer.
  • The corrected time is only as good as the past prints. Prints of one kind of job, on the same profile, give a better factor than a mix. Enter the clock time from start to finish, including heating if you want it counted.
  • Every starting value except the printer’s watts and the filament densities is an example. The watts and densities are the makers’ own figures; the sources are in the table below.
  • The cost is for machine time only. Filament, your own time, fees and tax are in the price calculator.

Preset figures and where they come from

Each figure was read on the company’s own page, checked on 15 November 2026.

PresetFigureSource
Bambu Lab A195 Wwiki.bambulab.com
Bambu Lab A1 mini80 W
Bambu Lab P1S105 W
Bambu Lab X1 Carbon105 W
Bambu Lab P2S200 W
Bambu Lab H2D197 W
Bambu Lab H2S200 W
Bambu Lab H2C200 W
Bambu Lab X2D250 W
Prusa MK4S80 Wprusa3d.com
Prusa Core One90 Wprusa3d.com
Bambu Lab PLA Basic1.24 g/cm³cdn.shopify.com
Polymaker PolyTerra PLA1.31 g/cm³polymaker.com
Polymaker PolyLite PLA1.17 g/cm³wiki.polymaker.com

Every preset is only a starting value. Change any field if your account, country or plan differs.

Questions sellers ask

How accurate is the slicer’s print time estimate?

It depends on the printer, the profile and the model, and nobody can tell you your own figure without your prints. A slicer only knows the speeds and accelerations in its machine profile, so when the printer does not reach them the real time runs longer. The way to find out is to measure: note the slicer’s estimate and the clock time for a few prints and enter them above.

Why does my 3D print take longer than the slicer says?

The estimate covers the moves in the file. It may leave out heating the bed and nozzle, levelling or calibration routines the printer runs first, pauses to change filament, and the time the printer spends slowing in corners and on small features. Because those vary by printer, the useful fix is a factor taken from your own prints, which is what the top half of this page works out.

How do I calibrate a slicer’s time estimate?

Divide the time your printer took by the time the slicer gave, over a few prints, adding the times up first. As an illustration, if 4.0, 2.0 and 6.0 hours of slicer time took 4.6, 2.3 and 6.8 hours, 13.7 ÷ 12.0 gives a factor of 1.14. A job the slicer rates at 5 h 30 min then comes to 6 h 17 min.

How do I estimate 3D print time without a slicer?

Work out the plastic volume, then divide by the flow, which is line width times layer height times speed. A 45 g part in PLA at 1.24 g/cm³ is 36.3 cm³. At a 0.42 mm line, 0.2 mm layers and 100 mm/s average speed the flow is 8.4 mm³/s, so the printing time is 1.20 hours, or 1.56 hours with 30% overhead. Treat it as rough: a slicer’s figure is better.

How do I work out what a print’s machine time costs?

Multiply the print time by the cost of an hour. With the example machine, a good print hour costs $0.19, so the 5 h 30 min print costs $1.06 in machine time. Charging at a 30% margin takes the hourly figure to $0.27 and the machine time to $1.51. Change the printer fields to your own, or use the cost per hour calculator to see where each part comes from.